Static Dissipative Floor Coating

  • Description

    The most advanced polymer floor coating to effectively control electrostatic discharge (ESD) on all hard surfaces. Contains Zoran™, an NCL exclusive, which is essential in the dissipation of charges form static electricity. NO-ZAP™ was developed to meet the demanding needs of the electronic, microchip and telecommunications industries. This premium, high solids floor finish can be maintained with a variety of methods, and is formulated to be extra durable, resist marking, and produce an immediate wet-look gloss.

    Authorized UL Product

    Key Market Information

    In production facilities where electrostatic charges can present problems, floor techs can not use just any coating. NO-ZAP™ STATIC DISSIPATIVE FLOOR COATING with Zoran, dissipates the charges from static electricity, evenly throughout the floor. This is a must have in any facility in the electronic, telecommunications, or microchip industries.
    Code: 2600
    Packaging: 4 x 1 Gal./Case
  • Specifications

    • TypePure acrylic polymers
    • pH8.2 ± 0.1
    • Specific Gravity (g/cc)1.03 ± 0.01
    • Coverage (sq. ft. / gal)2500
    • Drying Time (minutes)40-60
    • ColorWhite, opaque liquid
    • OdorTypical
    • acrylic Film AppearanceClear
    • PowderingNone
    • Flash PointNone
    • Slip ResistantYes
  • Disinfectant Efficacy

  • Documentation

    Technical Data Sheet No-Zap Floor Coating TDS English GHS.pdf Safety Data Sheet NO-ZAP COATING SDS English.pdf Miscellaneous Documents No-Zap Brochure.pdf Miscellaneous Documents No-Zap Finish (Undiluted) GHS Secondary Label 6 up.pdf
  • Directions

    Floor Preparation: Use a recommended floor stripper for removal of old finish from floors where static control is desired. Strip and remove solutions from floor with mop or wet dry vacuum. Rinse thoroughly with clean water and allow to completely dry.

    Application: Using a clean mop or applicator apply a thin uniform coat of NO-Zap™. Allow to dry for 40-60 minutes after each coat. Do not apply more than 3 coats. Floor should be thoroughly dry before traffic is allowed in area.

    NOTE: Avoid applying of NO-ZAP™ Static Dissipative Floor Coating under high humidity conditions. This product contains Zoran™, which absorbs water from the atmosphere and can affect the properties of the floor coating. Wait 72 hours after application before cleaning, buffing or re-coating.

    Restorative Maintenance:

    Mopping with NO-ZAP™: If floor surface is relatively clean, use NO-ZAP™ Static Dissipative Floor Coating at a 1:1 dilution with cool water and apply to improve floor resistivity.

    Damp Mopping: Use NCL ENHANCE Neutral Floor Cleaner at a ratio of 1 oz. per gallon of water for mopping and 1 oz. per gallon of water for auto-scrubbing.

    Spray Buffing with 1000 RPM equipment or higher: Use NO-ZAP™ Static Dissipative Floor Coating at a dilution of 1 part finish to 5 parts water. Buff floor using white or light colored synthetic pad.

    Re-coating: Perform re-coating when the floor resistivity is above 109 ohms, or as required.

  • Features & Benefits

    • Contains NCL exclusive Zoran™ for effective static control
    • High solids formula resists scratching and wear
    • Produces an immediate wet-look gloss
    • Easy to clean and maintain; resists soil retention
    • Recommended for use on hard surface floors and VCT.
  • Video

  • Safety

    Precautionary statement:
    Prevention: Observe good industrial hygiene practices.
    Response: Wash thoroughly after handling.
    Storage: Store away from incompatible materials.
    Disposal: Dispose of contents/container in accordance with local/regional/national/international regulations. This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
    Additional safety measures:
    Read the entire label and SDS before using this product, and for additional first aid measures. SDS for this product is available under the Documents tab.

Companion Products